Alto MIXPACK Pro

MIXPACK Pro doesn't stop with professional amplification and speakers. An eight-channel mixer is included so you can connect everything from musical instruments to microphones to an iPod. Four simple screws can be removed allowing the mixer portion to be detached and conveniently placed into your audio rack so you don't have to bend over to make adjustments during a show. Maybe your band is gigging or you are a live sound engineer or sound contractor looking for something you can set up quickly without sacrificing quality or power, Regardless of where the performance takes you, MIXPACK Pro is easy to set up with all the right connections.  Stands are included and tuck neatly within the cabinet for transport so you can get the sound where it needs to go without any hassle.

Once all your gear is connected to MIXPACK Pro, you can go to work on fine tuning for the venue with MIXPACK Pro's built-in 24-bit digital effects and 7-band graphical EQ. Effects include Hall, Room Vocal & Plate Reverb, Mono & Stereo Delay (max Delay Time 650ms) Chorus, Flanger & Reverb Modulations, Stereo Delay Chorus Rev+Delay and Rev+Chorus combinations. 256 total effects spread across 16 types with 16 variations mean that you are always ready for any room and any performance. 

When you need to get in and out in a hurry with high-power, clarity and flexibility, MIXPACK Pro is the ultimate portable PA choice. Also available are the 600W MIXPACK and 350W MIXPACK Express. 

TECH INFORMATION

Type: 3-Way Powered System Bi-Amp plus passive crossover into satellite
Low Output Power: 230 Watts RMS Class AB 
MID-HIGH-Output Power: 120 W + 120 Watts RMS Class AB
Peak Power Ratling: 1000 Watts Peak
Maximum SPL @ 1m: 119.5 dB Continuous - 122.5 dB Peak (calculated) 
Frequency Response:  45 Hz - 20 kHz @ -10 dB
Impedance: Low-Mid/High Low 4 Ohm - Mid/high 8 Ohm 
Crossover Frequencies: Active 125 Hz at 12 dB / Oct - Passive 3000 Hz at 12 dB / Oct with Electronic Dynamic Protections
Amplifier Protections: Low-Mid / High Soft start - Short Circuit - DC output voltage - Thermal Protection - Subsonic Filter at 30 Hz - 24 dB / Oct - Limiter / Compressor 
Low Frequency Device: 15" / 385 mm - 2.5" Voice Coil 
Mid Frequency Device: 4 × 6.5" / 165 mm - 1.5" Voice Coil
High Frequency Device: 2 × 1 "Compression Driver - 1" Voice Coil
Horn Coverage: 80° H × 80° V
Enclosure: Plastic Reinforced Cabinet Polypropylene

Mixer Section
Microphone Input: Electronically balanced discrete input configuration
Frequency Response: 10 Hz to 55 kHz +/-3 dB
Distortion (THD&N): 0.04% at +4 dBu 1 kHz
Gain: 35 dB
SNR (Signal to noise ratio): ＞94 dB
Line input: Electronically balanced 
Frequency Response: 10 Hz to 55 kHz +/-3 dB
Distortion (THD&N): 0.04% at +4 dBu 1 kHz
Gain: 15 dB

Stereo input / Output
Line input: Unbalanced
Frequency Response: 10 Hz to 55 kHz +/-3 dB
Distortion (THD&N): 0.04% at +4 dBu 1 kHz

Impedances
Microphone Input: 1.4 kOhm
Channel insert retum: 2.5 kOhm
All other inputs: 10 kOhm or greater
Tape out: 1 kOhm
All other outputs: 120 ohm

Equalization
Hi shelving: ±15 dB @ 12 kHz
Mid bell: ±15 dB @ 2.5 kHz
Low shelving: ± 15 dB @ 80 Hz

Alesis DSP Section
A/D and D/A converters: 24-bit
DSP resolution: 24-bit
Type of effects: Hall, Room, Vocal & Plate Reverbs, Mono & Stereo Delay (max Delay Time 650ms), Chorus, Flanger & Reverb Modulations, Reverbs, Stereo Delay, Chorus, Reverb + Delay and Reverb + Chorus combinations.
Presets: 256
Controls: 16-position preset selector 16-position Variation selector 

Controls & Monitoring
16-position preset selector
Clip LED
Mute Switch with LED indicator

Main Mix Section
Noise (Bus noise)
Fader 0 dB channels muted: -85dB (ref:+4dBu)
Fader 0 dB all input channels assigned and set to unity gain: -81 dBr (ref: +4 dBu)
Max output: 27 dBu balanced
Controls: 22 dBu balanced 1/4" jacks
AUX Sends: Max out 22 dBu
Power Supply: AC - 220 / 240 Volt or AC-100 / 120 Volt, with Switching Power Mode.

Dimensions (WxLxH): 1060mm x 700mm x 700mm
Weight: 111.8 lb